Verified 200-301 dumps Q&As 100% Pass in First Attempt Guaranteed Updated Dump from Braindumps2go
Pass CCNA 200-301 Exam With 898 Questions
IP Connectivity: This part focuses on the proficiency of the test takers in the following:
- Setting and verifying single area OSPFv2
- Setting and verifying IPv4 & IPv6 static routings
- Understanding the components of a routing table
- Describing the aim of FHRP
- Determining the ways how routers can perform forwarding decisions
Cisco 200-301 certification exam is an entry-level exam that tests the knowledge and skills of professionals in the field of network engineering. Cisco Certified Network Associate Exam certification is designed to validate the candidate's knowledge and understanding of basic networking concepts, including network access, IP connectivity, IP services, security fundamentals, and automation and programmability. The Cisco 200-301 certification exam is essential for anyone who wishes to start a career in the field of networking.
NEW QUESTION # 288
Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?
- A. These commands need to be added to the configuration:
C-router(config)# router ospf 1
C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0 - B. These commands need to be added to the configuration:
C-router(config)# router rip
C-router(config-router)# network 172.19.0.0 - C. No further routing configuration is required.
- D. These commands need to be added to the configuration:
C-router(config)# router eigrp 123
C-router(config-router)# network 172.19.0.0
Answer: C
Explanation:
Since all the same router (C-router) is the default gateway for all three VLANs, all traffic destined to a different VLA will be sent to the C-router. The C-router will have knowledge of all three networks since they will appear as directly connected in the routing table. Since the C-router already knows how to get to all three networks, no routing protocols need to be configured.
NEW QUESTION # 289
How will Link Aggregation be Implemented on a Cisco Wireless LAN Controller?
- A. One functional physical port is needed to pass client traffic.
- B. The EthernetChannel must be configured in "mode active".
- C. When enabled, the WLC bandwidth drops to 500 Mbps.
- D. To pass client traffic, two or more ports must be configured.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration-guide/b_cg75/b_cg75_chapter_0100010.html
Answer: A
NEW QUESTION # 290
Drag and drop the WLAN components from the left onto the correct descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 291
Drag and drop the TCP or UDP details from the left onto their corresponding protocols on the right.
Answer:
Explanation:
NEW QUESTION # 292
Refer to the exhibit.
An engineer is configuring the router to provide static NAT for the webserver Drag and drop the configuration commands from the left onto the letters that correspond to its position in the configuration on the right.
Answer:
Explanation:
NEW QUESTION # 293
A network engineer is implementing a corporate SSID for WPA3-Personal security with a PSK.
Which encryption cipher must be configured?
- A. CCMP256
- B. CCMP128
- C. GCMP256
- D. GCMP128
Answer: B
Explanation:
WPA3 mandates the adoption of Protected Management Frames, which help guard against eavesdropping and forging. It also standardizes the 128-bit cryptographic suite and disallows obsolete security protocols. WPA3-Enterprise has optional 192-bit security encryption and a 48- bit IV for heightened protection of sensitive corporate, financial and governmental data. WPA3- Personal uses CCMP-128 and AES-128.
NEW QUESTION # 294
Refer to the exhibit. Based on the LACP neighbor status, in which mode is the SW1 port channel configured?
- A. passive
- B. active
- C. mode on
- D. auto
Answer: B
Explanation:
From the neighbor status, we notice the "Flags" are SP. "P" here means the neighbor is in Passive mode.
In order to create an Etherchannel interface, the (local) SW1 ports should be in Active mode.
Moreover, the "Port State" in the exhibit is "0x3c" (which equals to "00111100 in binary format).
Bit 3 is "1" which means the ports are synchronizing -> the ports are working so the local ports should be in Active mode.
Reference:
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3650/software/release/3se/consolidat ed_guide/command_reference/b_c
NEW QUESTION # 295
Drag and drop the SNMP components from the left onto the descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 296
Router R1 must send all traffic without a matching routing-table entry to 192.168.1.1. Which configuration accomplishes this task?
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: C
NEW QUESTION # 297
Refer to the Exhibit.
After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1.
which error must be corrected?
- A. The PCs are m the incorrect VLAN
- B. Access mode is configured on the switch ports.
- C. All VLANs are not enabled on the trunk
- D. There is a native VLAN mismatch
Answer: D
NEW QUESTION # 298
What role does a hypervisor provide for each virtual machine in server virtualization?
- A. Software-as-a-service
- B. control and distribution of physical resources
- C. infrastructure-as-a-service.
- D. services as a hardware controller.
Answer: B
Explanation:
The hypervisor creates and manages virtual machines on a host computer and allocates physical system resources to them.
NEW QUESTION # 299
Refer to the exhibit.
A network engineer must configured communication between PC A and the File Server. To prevent interruption for any other communications, which command must be configured?
- A. Switchport trunk allowed vlan remove 10-11
- B. Switch trunk allowed vlan 12
- C. Switchport trunk allowed vlan add 13
- D. Switchport trunk allowed vlan none
Answer: C
NEW QUESTION # 300
Refer to the exhibit.
The New York router is configured with static routes pointing to the Atlanta and Washington sites. Which two tasks must be performed so that the Serial0/0/0 interfaces on the Atlanta and Washington routers can reach one another?
(Choose two.)
- A. Configure the ipv6 route 2012::/126 2023::1 command on the Washington router.
- B. Configure the ipv6 route 2023::/126 2012::2 command on the Atlanta router.
- C. Configure the ipv6 route 2012::/126 2023::2 command on the Washington router.
- D. Configure the Ipv6 route 2012::/126 s0/0/0 command on the Atlanta router.
- E. Configure the ipv6 route 2023::/126 2012::1 command on the Atlanta router.
Answer: B,C
Explanation:
The short syntax of static IPv6 route is: ipv6 route <destination-IPv6-address> {next-hop-IPv6-address | exit-interface}
NEW QUESTION # 301
A network engineer is configuring a switch so that it is remotely reachable via SSH The engineer has already configured the host name on the router Which additional command must the engineer configure before entering the command to generate the RSA key?
- A. ip ssh authentication-retries 2
- B. ip domain-name domain
- C. crypto key generate rsa modulus 1024
- D. password password
Answer: B
Explanation:
https://www.cisco.com/c/en/us/solutions/small-business/resource-center/networking/how-to-setup-network-switch.html
NEW QUESTION # 302
Drag and drop the IPv6 address types from the left onto their description on the right.
Answer:
Explanation:
NEW QUESTION # 303
Where does a switch maintain DHCP snooping information?
- A. In the CAM table
- B. In the binding database
- C. In the MAC address table
- D. In the frame forwarding database
Answer: B
Explanation:
Section: Security Fundamentals
NEW QUESTION # 304
Refer to the exhibit.
An engineer deploys a topology in which R1 obtains its IP configuration from DHCP. If the switch and DHCP server configurations are complete and correct. Which two sets of commands must be configured on R1 and R2 to complete the task? (Choose two)
- A. R2(config)# interface gi0/0
R2(config-if)#ip address dhcp - B. R1(config)# interface fa0/0
R1(config-if)#ip helper-address 198.51.100.100 - C. R1(config)# interface fa0/0
R1(config-if)#ip helper-address 192.0.2.2 - D. R1(config)# interface fa0/0
R1(config-if)#ip address dhcp
R1(config-if)# no shutsown - E. R2(config)# interface gi0/0
R2(config-if)#ip helper-address 198.51.100.100
Answer: D,E
NEW QUESTION # 305
......
Cisco 200-301 exam covers a wide range of topics related to networking, including network fundamentals, network access, IP connectivity, IP services, security fundamentals, automation, and programmability. 200-301 exam includes multiple-choice questions, simulation questions, and drag-and-drop questions. 200-301 exam duration is 120 minutes, and the passing score is 825 out of 1000.
Pass 200-301 Tests Engine pdf - All Free Dumps: https://braindumps2go.dumptorrent.com/200-301-braindumps-torrent.html